We have a wide range of auxiliaries to facilitate the printing work:

FLEXOGRAPHY

  1. Drying Accelerator IP-55
  2. Retardant of Drying RS962
  3. Antifoam HK7
  4. Defoamer MSP59
  5. PH corrector
  6. Ecoflex FX07 click cleaner
  7. Rodiflex anilox cleaner WK-09
  8. Moisturizer Substrate NFS

 

DIGITAL

  1. Cleaner
  2. Printhead cleaner
  3. Printhead recovery
  4. Liquid decapping long idle

 


Drying Accelerator IP-55

High efficiency accelerator for general use in aqueous systems. Specific for water and gravure flexographic inks. Increase drying

Specifications

  • Appearance: Clear liquid without suspended matter
  • Specific weight: 0.7 ± 0.8 gr / cm3
  • Smell: Not residual
  • Viscosity: 10-15 Sec. DIN 4 mm. at 20ºC

Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment.

Recommended dose: between 0% and 5%. Do not exceed the maximum amount recommended as there may be defects in the impression, such as craters or fish eyes.

Storage and presentation

Store in a ventilated and fresh place. Due to its alcoholic character, it must not endure large temperature variations.

The product is marketed in a 25 kg and 10 kg carafe.

The storage temperature should be between 12ºC and 30ºC.

Expiration of 12 months

Retardant of Drying RS962  

High efficiency retardant for general use in aqueous systems. Specific for water and gravure flexographic inks. Delays drying
 
Specifications
  • Appearance: Clear liquid without suspended matter
  • Specific weight: 1 ± 1.1 gr / cm3
  • Smell: Not residual
  • Viscosity: 10-20 Sec. DIN 4 mm. at 20ºC

Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment.

Recommended dose: between 0% and 5%. Do not exceed the maximum amount recommended as there may be defects in the impression, such as craters or fish eyes.

Storage and presentation

Store in a ventilated and fresh place. Due to its alcoholic character, it must not endure large temperature variations.

The product is marketed in 10kg carafe.

The storage temperature should be between 12ºC and 30ºC.

Expiration of 12 months

Antifoam HK7

Prevents the formation of foam in the printing ink, good long-term effectiveness.

Specifications

  • Appearance: Milky liquid not very dense
  • Specific weight: 1.06 ± 0.1 gr / cm3
  • PH value: 8.0-8.20
  • Viscosity: 30-35 Sec. DIN 4 mm. at 20ºC

Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment. It can be used according to the form of supply or diluted with water.

Recommended dose: between 0.10% and 0.50%. Do not exceed the maximum amount recommended as there may be defects in the impression, such as craters or fish eyes.

Being a totally innocuous product, it can be handled without special precautions.

Storage and presentation

Store in a ventilated and fresh place. Due to its emulsion character, it must not endure large temperature variations.

The product is marketed in 25 kg, 20 kg and 10 kg carafes.

The storage temperature should be between 12ºC and 35ºC.

Expiration of 12 months

Defoamer MSP59

High efficiency defoamer for general use in aqueous systems. Specific for water and gravure flexographic inks. It instantly removes both the foam and the microfoam that can be generated during the printing process in an ink.

Specifications

  • Appearance: Thin translucent fluid
  • Density: 1.02 ± 0.1 gr / cm3
  • PH value: 8.0-8.20

Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment. It can be used according to the form of supply or diluted with water.

Recommended dose: between 0.10% and 0.50%. Do not exceed the maximum amount recommended as there may be defects in the impression, such as craters or fish eyes.

Being a totally innocuous product, it can be handled without special precautions.

Storage and presentation

Store in a ventilated and fresh place. Due to its emulsion character, it must not endure large temperature variations.

The product is marketed in 25 kg, 20 kg and 10 kg carafes.

The storage temperature should be between 12ºC and 35ºC.

Expiration of 12 months

PH corrector

Mix of alkalinizers with controlled volatility to increase the pH of an ink when needed. It is frequent that due to an inadequate storage, prolonged in time or due to anomalous circumstances of excessive heat, it can happen that the alkaline substances that stabilize the ink, evaporate and this produces a drop in pH and consequently its printability is diminished.

Our inks work correctly in a pH range between 8.50 and 9.0. With the pH corrector it is possible to reach this interval with very small additions.

Specifications

  • Appearance: Thin translucent fluid
  • Density:        1.02 ± 0.1 gr / cm3
  • PH value:     12.0 ± 0.1

Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment. It is advised before use to consult the safety data sheet.

It can be used according to the form of supply or diluted with water.

Recommended dose: depending on the starting pH: between 0.10% and 0.40%.

Ecoflex FX07 cliche cleaner

Stripper of water-based flexographic inks, especially suitable for cleaning the photopolymer cliches. Its formula, specially designed for this type of application, allows to use it manually or in automatic washing machines. This product can be discharged together with the effluents of the treatment plant without any problem since it does not affect the usual cleaning processes in flexographic inks.

Specifications

  • Appearance: Dense liquid
  • Density: 1.05 ± 0.1 gr / cm3
  • PH value: 8.0 - 9.0

Manipulation and storage

Product of low causticidad and innocuous, does not irritate the skin being able to work with the hands without any problem.

Stability

Stable to heat. Given its slight alkaline character, do not mix with strong oxidizing acid products.

Conservation

Keep in a ventilated and fresh place, away from any acidic product.

                             

Rodiflex anilox cleaner WK-09

Stripper of water-based flexographic inks, specially indicated to eliminate any remaining ink, both in the inkwell and in any part of the printing machine. Its formula, specially designed for this type of application, allows to use it on any component : rubber, plastic, aluminum, steel or zinc, without these surfaces being attacked.

Specifications

  • Appearance: Low density liquid
  • Density: 1.06 ± 0.1 gr / cm3
  • PH value: 11.5 - 12


Indicted

Product with high causticity and irritant in contact with the skin, so it is advisable to use precautionary measures. These are prescribed in the safety data sheets.

Storage and presentation

Store in a ventilated and fresh place.

The product is marketed in 25 kg, 20 kg and 10 kg carafes.

The storage temperature should be between 12ºC and 35ºC.

Stable to heat. Given its strong alkaline character, do not mix with strongly oxidizing acid products.

Expiration of 12 months.

Moisturizer Substrate NFS

Specifically designed to help wet the ink on substrates that are not very absorbent or difficult to moisten, without causing a stabilization of the foam in the system. It acts as a good antifoam.

Specifications

  • Appearance: Transparent liquid
  • Specific weight: 0.91 gr / cm3
  • pH: 7.2 - 7.8
  • Viscosity: 12-14 Sec. DIN 4 mm. at 20ºC


Indicted

Add to the ink always in agitation to avoid possible flocculation of the pigment.

It can be used according to the form of supply or diluted with water.

Recommended dose: between 0.40% and 1%.

Storage and presentation

Store in a ventilated and fresh place. Flammable compound.

The product is marketed in 25 kg, 10 kg and 5 kg carafes.

The storage temperature should be between 12ºC and 35ºC.

Expiration of 12 months.